Wszystkie karty
Calorimetry
- What is assumed about the specific heat capacity of a dilute aqueous solution in Q = mcΔT?That it is the same as that of pure water, 4.18 J g⁻¹ K⁻¹.
- What is assumed when 50.0 cm³ of solution is taken as 50.0 g?That the density of the solution is the same as water, 1.00 g cm⁻³.
- What is assumed about where the heat released by the reaction goes?All of it is absorbed by the solution (or water): no heat is lost to the surroundings and none is absorbed by the cup, thermometer or can.In reality heat is lost, so the measured ΔH is less negative than the true value (smaller in magnitude).
- What is assumed about the calorimeter itself?Its heat capacity is negligible: it absorbs no significant heat.
- 25.0 cm³ of acid is mixed with 25.0 cm³ of alkali and the volume is taken as 50.0 cm³. What is assumed?That the volumes are additive (no change in volume on mixing).
- Zinc powder is added to copper(II) sulfate solution and only the mass of the solution is used for m. What is assumed?That the solid added has a negligible effect on the mass and heat capacity of the mixture.
- What is assumed about the fuel in a combustion calorimetry experiment?It burns completely to carbon dioxide and water, and all the mass lost by the burner is fuel that was burned.Soot on the can shows incomplete combustion; evaporation from the wick makes the mass loss too large.
- What is assumed about the reaction when ΔH is calculated from the moles of the limiting reactant?That the limiting reactant reacts completely and there are no side reactions.
Gases
- State the assumptions of the ideal gas model.Particles are in continuous random motion; their volume is negligible compared with the volume of the container; there are no intermolecular forces between them; all collisions are perfectly elastic.The kinetic energy of the particles is proportional to the temperature in kelvin.
- Under which conditions do real gases deviate most from ideal behaviour, and why?At high pressure and low temperature. The particles are close together, so their own volume is no longer negligible, and they move slowly, so intermolecular forces become significant.
- What is assumed when a volume of gas is converted to moles with the molar volume?That the gas behaves ideally and is at the stated conditions (e.g. STP).
- What is assumed when the volume of gas in a syringe or measuring cylinder is taken as the gas produced?No gas escapes before the bung is fitted, the gas is the only product collected and it does not dissolve in water.CO2 is fairly soluble in water, so collecting it over water gives a volume that is too small.
Bond enthalpies and Hess’s law
- Why is ΔH calculated from bond enthalpies only approximate?Bond enthalpies are average values taken over many different compounds, and they apply to substances in the gaseous state.If a reactant or product is a liquid (e.g. water), the energy of the change of state is ignored.
- What is assumed about the states of all species when bond enthalpies are used?That all reactants and products are gases.
- What does Hess’s law rely on?The enthalpy change of a reaction depends only on the initial and final states, not on the route taken.
Rates
- What is assumed when 1/t is used as the rate of reaction?That the same amount of product forms each time before the end point (e.g. the cross disappears) and the rate is roughly constant over that time.1/t is an average rate, closest to the initial rate when t is short.
- What is assumed when the initial rate is used to compare concentrations?That the concentrations of the reactants have not changed significantly during the time measured.
- What is assumed when the loss of mass of a flask is taken as the mass of CO2 produced?That carbon dioxide is the only substance that escapes: no water vapour or acid spray is lost.
Titrations and stoichiometry
- What is assumed about a sample when its purity is found by titration?Only the substance being analysed reacts with the titrant; the impurities do not react.
- What is assumed about the colour change of the indicator?That the end point (colour change) coincides with the equivalence point.
- What is assumed about the reaction in a titration calculation?It goes to completion with the stoichiometry given by the equation.
- What is assumed when the concentration of a coloured species is read from a calibration curve?That only that species absorbs at the chosen wavelength and the absorbance is proportional to concentration over the range used.
- What is assumed when measured concentrations are put into the expression for K?That the mixture has reached equilibrium in a closed system and the temperature is constant.K changes only with temperature.
- What is assumed when the theoretical yield is calculated?The limiting reactant is converted completely into the product, with no side reactions and no losses.
Weak acids, equilibria and cells (HL only)
- In a weak acid pH calculation with Ka, what is assumed about [HA]?That the equilibrium concentration of HA equals its initial concentration, because only a tiny fraction dissociates.Fails when the acid is not very weak (larger Ka) or very dilute.
- In the same calculation, what is assumed about [H+] and [A−]?That they are equal, and that the H+ from the ionization of water is negligible.
- What is assumed when Kw = 1.00 × 10−14 is used?That the temperature is 298 K. Kw increases with temperature.
- What is assumed about [HA] and [A−] when the pH of a buffer is calculated?They are taken as their initial values: the dissociation of the acid and the hydrolysis of the salt are negligible.
- What is assumed when Ea is found from a plot of ln k against 1/T?That the activation energy and the Arrhenius factor are constant over the temperature range used.
- What is assumed when Ecell⊖ from the data booklet is used to predict a real cell?Standard conditions: 298 K, 1 mol dm⁻³ solutions and 100 kPa for gases. Different conditions change the actual cell potential.
Sprawdź się na prawdziwych zadaniach: zadania w stylu arkuszy IB z kluczem.