Wszystkie karty
Solutions and measuring
- How do you make an accurate dilution of a stock solution?Transfer the stock with a volumetric pipette (or burette) into a volumetric flask, fill to the mark with distilled water, stopper and invert several times.Volume of stock = c2V2/c1.
- What is a serial dilution and what is it used for?Diluting a solution step by step by the same factor each time (e.g. 1 in 10). It makes a set of standards, for example for a calibration curve.
- Which glassware measures volume most precisely, and which least?Most: volumetric pipette and volumetric flask (one fixed volume). Then burette (variable volume). Least: measuring cylinder and beaker.
- What is weighing by difference and why is it used?Weigh the container with the solid, tip the solid out, weigh the container again. The difference is the mass actually transferred, even if some stays in the container.
- Describe drying to constant mass.Heat, cool, weigh, and repeat until two consecutive masses agree within the uncertainty of the balance.
- Why is a hot crucible cooled in a desiccator before it is weighed?A hot object creates air currents that disturb the balance reading, and a cooling solid can absorb water from the air. The desiccator keeps the air around it dry.
- How is a pH meter prepared and used?Calibrate it with buffer solutions of known pH (e.g. 4, 7 and 10), rinse the probe with distilled water between solutions, and wait for a steady reading.
- Give advantages of a temperature sensor and data logger over a thermometer read by eye.More precise readings, no reading errors, many readings taken automatically at short intervals, data ready for a graph.
Heating and separating
- What is heating under reflux and why is it used?Heating with a vertical condenser so vapours condense and drip back into the flask. The mixture can be heated for a long time without losing volatile reactants or products.Used to oxidize a primary alcohol all the way to a carboxylic acid.
- When is distillation used instead of reflux in organic chemistry?When a volatile product should be removed as it forms, e.g. distilling off the aldehyde so it is not oxidized further to the carboxylic acid.
- Why does cooling water enter the condenser at the bottom and leave at the top?The jacket fills completely with water, so cooling is efficient along its whole length.
- Why must a reflux apparatus never be sealed at the top?Heating a closed system builds up pressure and the apparatus could explode.
- Why are anti-bumping granules added before heating a liquid?They give smooth boiling and stop large bubbles forming suddenly (bumping).
- When is fractional distillation needed?To separate miscible liquids whose boiling points are close together.
- What is a separating funnel used for?Separating two immiscible liquids; the denser layer is run off from the bottom.Open the tap from time to time while shaking to release pressure.
- Describe recrystallization of an impure solid.Dissolve it in the minimum volume of hot solvent, filter while hot to remove insoluble impurities, cool slowly so crystals form, filter, wash with a little cold solvent and dry.Soluble impurities stay in the solution because there is too little of them to crystallize.
- Why is the minimum volume of hot solvent used in recrystallization?So the solution is saturated: as much product as possible crystallizes on cooling, giving a higher yield.
- How does a melting point show whether a solid is pure?A pure solid melts sharply at the literature value. An impure solid melts lower and over a wider range.
- What advantages does thin layer chromatography have over paper chromatography?It is faster and gives better separation. Colourless spots can be seen under UV light or with iodine.
Colorimetry and safety
- Which wavelength or filter is chosen to measure a coloured solution in a colorimeter?The one the solution absorbs most strongly: the complementary colour to the colour seen (use the colour wheel).A blue solution absorbs orange light.
- How is a calibration curve made and used?Measure the absorbance of several standards of known concentration and plot absorbance against concentration. Read the unknown concentration off the line from its absorbance.
- Why is a cuvette of pure solvent measured first?It sets the zero (the blank), so only the absorbance of the solute is measured.Hold the cuvette by its frosted sides; fingerprints absorb light.
- When must a reaction be done in a fume hood?When a toxic or irritating gas or vapour is produced or used, e.g. SO2, Cl2, Br2, NO2.
- How are flammable organic liquids heated safely?With a water bath or electric heating mantle, never a naked flame.
- What precautions are needed with concentrated acids and alkalis?Goggles and gloves; add acid to water slowly, not water to acid; wipe up spills straight away.For an answer to score, link the hazard to the precaution: corrosive, so goggles and gloves.
Sprawdź się na prawdziwych zadaniach: zadania w stylu arkuszy IB z kluczem.