Wszystkie karty
Recording uncertainties
- What is the usual uncertainty of a reading from an analogue scale (thermometer, measuring cylinder)?± half of the smallest division, e.g. ±0.5 °C for a thermometer marked every 1 °C.
- What is the uncertainty of a digital instrument (balance, digital thermometer)?± one unit in the last digit shown, e.g. ±0.01 g for a balance reading to 0.01 g.
- A burette is read to ±0.05 cm³. What is the uncertainty of the titre?±0.10 cm³: the titre is the difference between two readings, so the two uncertainties add.
- Initial and final temperatures are each ±0.5 °C. What is the uncertainty of ΔT?±1.0 °C. A difference of two readings has the sum of their absolute uncertainties.A temperature change in °C and in K is the same number, with the same uncertainty.
- Where does the uncertainty of a volumetric pipette or flask come from?It is printed on the glassware by the manufacturer, e.g. 25.00 ± 0.06 cm³.
- A digital stopwatch reads to 0.01 s. Is ±0.01 s a realistic uncertainty for timing a colour change by eye?No. Human reaction time (roughly 0.2 to 0.5 s) is much larger, so a realistic uncertainty is a few tenths of a second.
- How many decimal places should a raw measurement have?The same number as its uncertainty: 24.35 ± 0.05 cm³, not 24.3 ± 0.05 cm³. All values in a table column use the same precision.
- How are a final uncertainty and the value it belongs to rounded?The uncertainty usually to one significant figure; the value to the same decimal place as the uncertainty, e.g. 45 ± 3 kJ mol⁻¹.
Propagating uncertainties
- How do uncertainties combine when quantities are added or subtracted?Add the absolute uncertainties.
- How do uncertainties combine when quantities are multiplied or divided?Add the percentage (or fractional) uncertainties.Convert back at the end: absolute uncertainty = value × percentage uncertainty ÷ 100.
- A quantity is multiplied by an exact number (a mole ratio, or 1000 for a unit change). What happens to its uncertainty?The percentage uncertainty stays the same; the absolute uncertainty is multiplied by the same number.
- A quantity is raised to a power n. How does its percentage uncertainty change? (HL)It is multiplied by n: if x is ±2%, then x2 is ±4%.
- What is the percentage uncertainty of Q = mcΔT?Percentage uncertainty of m plus percentage uncertainty of ΔT. The value of c is treated as exact.
- How can the uncertainty of the mean of repeated trials be estimated?As half the range: (largest − smallest) ÷ 2.Take the larger of this and the instrument uncertainty.
- How do you decide which measurement to improve to reduce the overall uncertainty?Compare the percentage uncertainties: improve the one with the largest, e.g. a small ΔT measured with a ±0.5 °C thermometer.Increase the quantity measured (larger mass, larger ΔT) or use a more precise instrument.
Errors, accuracy and precision
- What is a random error and how is it reduced?An unpredictable variation in readings, above or below the true value. It is reduced by repeating measurements and taking the mean.Random errors affect precision.
- What is a systematic error and how is it reduced?An error that shifts every reading in the same direction. Repeats do not reduce it: change the method or calibrate the instrument.Systematic errors affect accuracy. Heat loss in calorimetry is the classic example.
- Accuracy or precision: which is which?Accuracy: how close a result is to the true or accepted value. Precision: how close repeated results are to each other.
- How is percentage error calculated?|experimental value − accepted value| ÷ accepted value × 100.Percentage error compares with the true value; percentage uncertainty describes your own measurement.
- The percentage error is 18% but the percentage uncertainty is only 4%. What does that tell you?Random errors cannot explain the difference: there must be significant systematic errors in the method.If the percentage error is smaller than the percentage uncertainty, random errors are enough to explain it.
- Is always reading a burette from above a random or a systematic error?Systematic: every reading is shifted the same way.An unscaled balance (zero error) is systematic too.
- Which answers to “identify a source of error” score no marks?“Human error”, “only one trial”, “random error” or “systematic error” on their own. Name the specific cause and its effect on the result.
- Independent, dependent and controlled variables: define each.Independent: the one you change. Dependent: the one you measure. Controlled: the ones kept constant so they do not affect the result.
- Continuous or discrete variable: give an example of each in chemistry.Continuous: can take any value in a range (temperature, concentration, time). Discrete: only separate values (number of carbon atoms, type of catalyst).Continuous data: line or scatter graph; discrete: bar chart.
Graphs
- How should a line of best fit be drawn?A single straight line or smooth curve with the points spread evenly on both sides. Never join the points dot to dot.
- What does a graph look like if y is directly proportional to x?A straight line passing through the origin.“Positive correlation” is not enough when a question asks for proportionality.
- What do you do with an anomalous point?Leave it out of the line of best fit, identify it and, if possible, repeat that measurement.
- How do you get the gradient of a line of best fit, and its units?Δy ÷ Δx using two points far apart on the line, not data points. The unit is the y unit divided by the x unit.
- What does the coefficient of determination R² tell you?How well the trend line fits the data: the closer to 1, the better the fit.A high R² says nothing about accuracy or about whether the right relationship was chosen.
- How is the uncertainty of a gradient estimated from a graph?Draw the steepest and the shallowest lines that still pass through all the uncertainty bars; half the difference between their gradients is the uncertainty.
- Why is extrapolation riskier than interpolation?It assumes the trend continues outside the range measured, which may not be true.
- What is the difference between drawing and sketching a graph?Draw: accurate, to scale, plotted points, ruler for straight lines. Sketch: labelled axes without a scale, showing the general shape and key features.
Sprawdź się na prawdziwych zadaniach: zadania w stylu arkuszy IB z kluczem.