IB Chemistry Paper 1B experiments: flashcards

Paper 1B is built around experiments. Most marks come from three questions: why is this step done, what went wrong, and how would you improve it. Each card takes one classic practical and asks exactly that.

43 karty · sprawdzono 9 listopada 2026 · ucz się z zapisem postępu

Ucz się karta po karcie

Pomyśl o odpowiedzi, odwróć kartę i oceń się uczciwie. Karty z „Nie wiem” wracają na koniec.

Calorimetry and Hess’s law1 / 43

Wszystkie karty

Calorimetry and Hess’s law

  • Why is a polystyrene cup with a lid used for a neutralization enthalpy experiment?Polystyrene is a thermal insulator and the lid stops heat escaping from the surface, so less heat is lost to the surroundings.Two cups nested inside each other insulate even better.
  • Why is the temperature–time graph extrapolated back to the time of mixing (e.g. zinc added to copper(II) sulfate)?To estimate the maximum temperature the solution would reach if the reaction were instantaneous, which compensates for heat lost to the surroundings while the reaction was happening.Draw the line through the cooling part of the curve and extend it back to the moment of mixing.
  • Why is zinc powder added in excess in the Zn + CuSO4 calorimetry experiment?So that all the Cu2+ ions react: copper(II) sulfate is then the limiting reactant and its amount sets the moles used to calculate ΔH. Powder reacts quickly, so heat is released before much is lost.
  • In Q = mcΔT for a reaction in solution, what mass is used for m?The mass of the whole solution (all liquids mixed), not the mass of the solid or of one reactant.Mass comes from volume, assuming a density of 1.00 g cm⁻³.
  • The temperature of the solution rose by 6.5 K. What is the sign of ΔH and how do you get ΔH in kJ mol⁻¹?Negative (exothermic). Divide Q by the moles of the limiting reactant and add the minus sign: ΔH = −Q/n.Forgetting the sign or dividing by the wrong amount are the two most common lost marks.
  • The enthalpy of combustion of a fuel measured with a spirit burner and a metal can is much less exothermic than the data booklet value. Give the main reasons.Heat lost to the air around the flame and the can; incomplete combustion (soot, CO); heat absorbed by the can and thermometer is not counted; some fuel evaporates from the wick.Say where the heat goes. “Heat loss” on its own is not accepted.
  • Why is the spirit burner weighed with its cap on and weighed again immediately after the flame is put out?The fuel is volatile: without the cap it evaporates, the mass loss is too large and the calculated ΔH is too small in magnitude.
  • Suggest improvements to a spirit burner and metal can combustion experiment.Shield the flame from draughts, put a lid on the can, reduce the distance between flame and can, use a copper can, stir the water.A bomb calorimeter is the ideal answer, but examiners usually expect simple changes to the given set-up.
  • Why is ΔH for Mg+12 OX2→MgO\ce{Mg + 1/2O2 -> MgO} found indirectly, from the reactions of Mg and MgO with hydrochloric acid?Burning magnesium cannot be done in a calorimeter in a controlled way: the heat cannot be measured reliably. The two reactions with acid can be measured, and Hess’s law combines them with ΔH for water.Same idea for hydrating anhydrous copper(II) sulfate: you measure two dissolutions instead.
  • Why is the initial temperature of both solutions recorded for some time before mixing?To make sure they have reached a steady temperature and to get a reliable starting value (the mean of both if they differ).

Rates of reaction

  • Magnesium reacts with hydrochloric acid and a gas syringe records the volume every 10 s. How do you get the initial rate?Plot volume against time and draw a tangent to the curve at t = 0: its gradient is the initial rate (in cm³ s⁻¹).The rate at any time is the gradient of the tangent at that time.
  • Sodium thiosulfate reacts with acid and the time for a cross under the flask to disappear is recorded. Why does the cross disappear and what is used as the rate?A precipitate of sulfur forms and makes the mixture opaque. 1/t is used as a measure of the (average) rate.The same amount of sulfur is needed each time to hide the cross, so a shorter time means a faster reaction.
  • Two students get different times for the same disappearing-cross experiment. Give specific reasons.Different judgement of when the cross disappears, different viewing angle or distance, different lighting, not starting the timer at the same moment, different temperature.“Human error” or “only one trial” on their own score nothing. Name the actual cause.
  • Which product of the thiosulfate and acid reaction needs a safety precaution, and which one?Sulfur dioxide gas, which is toxic and irritates the respiratory tract: work in a fume hood or a well-ventilated lab and wear goggles.A face mask is not an accepted precaution against a toxic gas.
  • Calcium carbonate reacts with acid in a flask on a balance. Why is a cotton wool plug put in the neck of the flask?It lets carbon dioxide escape but stops acid spray leaving the flask, so the mass loss is due to CO2 only.
  • Why is the reaction flask often placed in a water bath in a rate experiment?Temperature has a strong effect on rate, so it must be kept constant as a controlled variable.Exothermic reactions warm themselves up; a water bath limits that.
  • In an iodine clock reaction, why does the blue-black colour appear suddenly?A small fixed amount of thiosulfate reacts with the iodine as it forms. Once the thiosulfate is used up, free iodine forms a blue-black complex with starch at once.The time measures how long it takes to make a fixed amount of iodine, so 1/t is proportional to the rate.
  • How can a colorimeter follow the rate of a reaction?If a reactant or product is coloured, absorbance is proportional to its concentration (use a calibration curve), so absorbance against time gives concentration against time.
  • Marble chips are replaced by the same mass of powder. What happens to the initial rate and the final volume of CO2?The initial rate increases (larger surface area, more frequent collisions). The final volume stays the same if the acid and the mass of carbonate are unchanged.

Titrations

  • What should the burette, the pipette and the conical flask each be rinsed with?Burette: the solution it will contain. Pipette: the solution it will deliver. Conical flask: distilled water only.Water left in the flask does not change the moles of the analyte; water in the burette would dilute the titrant.
  • Which titres are used to calculate the mean?Concordant titres only, usually within 0.10 cm³ of each other. The first rough titre is left out.
  • How is a burette read and recorded?At eye level, from the bottom of the meniscus, to two decimal places (ending in 0 or 5), e.g. 23.45 cm³.
  • Why does a titration with potassium manganate(VII) need no indicator?The MnO4− ion is purple and is reduced to almost colourless Mn2+. The end point is the first permanent pale pink colour from a slight excess of MnO4−.The solution is acidified with dilute sulfuric acid, not hydrochloric acid, which manganate(VII) would oxidize to chlorine.
  • In an iodine–thiosulfate titration, when is starch added and why?Near the end point, when the solution is pale yellow. Added too early, a lot of iodine binds to the starch and is released slowly, so the end point is unclear.End point: blue-black to colourless.
  • When is a back titration used?When the substance is insoluble or reacts slowly (e.g. calcium carbonate in eggshell or an antacid tablet). A known excess of acid is added and the acid left over is titrated with a standard base.Moles that reacted = moles of acid added − moles of acid left over.
  • Why must a sodium hydroxide solution be standardized before it is used in a titration?Solid NaOH absorbs water and carbon dioxide from the air, so a weighed mass does not contain a precisely known amount of NaOH.It is titrated against a primary standard, e.g. potassium hydrogen phthalate.
  • Why is a white tile placed under the conical flask during a titration?So that the colour change at the end point is easier to see.
  • How do you prepare 250.0 cm³ of a standard solution from a solid?Weigh the solid accurately, dissolve it fully in a beaker of distilled water, transfer it with the rinsings to a 250.0 cm³ volumetric flask, fill to the mark with distilled water, stopper and invert several times.A measuring cylinder is not accepted for the final volume.

Equilibrium and electrochemistry

  • A pink solution of [Co(H2O)6]2+ turns blue ([CoCl4]2−) when heated. What does this tell you?Heating shifts the equilibrium towards the blue complex, so the forward reaction to [CoCl4]2− is endothermic.Adding concentrated HCl also turns it blue (more Cl−); adding water turns it pink.
  • More Fe3+ is added to the equilibrium Fe3+ + SCN− ⇌ [FeSCN]2+ (blood red). What is observed and why?The colour gets deeper red: the equilibrium shifts to the right to use up some of the added Fe3+.
  • What is the role of the salt bridge in a voltaic cell?It completes the circuit by letting ions move between the half-cells, which keeps each solution electrically neutral.Electrons flow through the external wire, never through the salt bridge.
  • Why is potassium nitrate a common choice for a salt bridge?Its ions do not react with the ions in the half-cells and do not form precipitates.For a silver half-cell KCl would be wrong: AgCl precipitates.
  • Why is a high-resistance voltmeter used to measure the cell potential?Almost no current flows, so the measured potential difference is the maximum the cell can give and the cell is not changed while it is measured.
  • Why are metal electrodes cleaned with sandpaper before they are used in a cell?To remove the oxide layer and dirt, which would change the reaction at the surface and the measured potential.
  • Molten lead(II) bromide is electrolysed. What forms at each electrode and what safety precaution is needed?Lead at the cathode (negative), bromine at the anode (positive). Bromine vapour is toxic and corrosive: use a fume hood.The solid does not conduct: the ions must be free to move, so it is melted first.

Composition and separation

  • Magnesium is heated in a crucible to find the formula of its oxide. Why is the lid lifted from time to time, but only briefly?Lifting it lets oxygen in so the magnesium reacts completely; closing it quickly stops white magnesium oxide smoke escaping.
  • Why might the mass of magnesium oxide obtained be lower than expected?Incomplete reaction, MgO smoke lost when the lid is lifted, some magnesium reacts with nitrogen to form Mg3N2.Clean the ribbon with sandpaper first to remove the oxide layer, and heat to constant mass.
  • Hydrated copper(II) sulfate is heated to find the number of water molecules. How do you know all the water has gone?Heat, cool and weigh repeatedly until two consecutive masses are the same: heating to constant mass. The solid also changes from blue to white.Overheating decomposes the anhydrous salt: too much mass is lost and the number of water molecules comes out too high.
  • In paper chromatography, why is the start line drawn in pencil and the solvent kept below it?Pencil (graphite) does not dissolve and move with the solvent, unlike ink. If the spots were below the solvent surface they would dissolve into the solvent instead of moving up the paper.
  • Why is the chromatography tank covered and the solvent front marked straight away?The lid keeps the air saturated with solvent vapour so the solvent does not evaporate from the paper. The front is marked at once because it fades as the solvent dries, and you need it to calculate Rf.
  • How is an Rf value calculated and how is it used?Distance moved by the spot divided by distance moved by the solvent front, both from the start line. A substance is identified by comparing its Rf with a known standard run under the same conditions.Rf has no unit and is always less than 1.
  • How would you separate a mixture of iron filings, sand and salt and find the mass of each?Remove iron with a magnet; add water to dissolve the salt; filter off the sand, wash and dry it; evaporate the water from the filtrate to get the salt. Dry each part to constant mass before weighing.Sieving is not accepted: the particles may be the same size.
  • Magnesium reacts with acid and the hydrogen is collected over water. Why can the molar volume calculated this way differ from the ideal value?The collected gas contains water vapour, some gas escapes before the bung is fitted, and the temperature and pressure are not exactly standard.A gas syringe avoids water vapour; correct the volume to the conditions you compare with.

Sprawdź się na prawdziwych zadaniach: zadania w stylu arkuszy IB z kluczem.

Inne fiszki z tego przedmiotu

Pliki cookies

Zapisujemy na Twoim urządzeniu to, bez czego serwis nie działa, np. zalogowanie. Plików analitycznych użyjemy tylko za Twoją zgodą. Szczegóły w polityce prywatności.